美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激!

yang13564

1.
4 z* c* Z  C- p. i: g4 {9 QQuality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
5 S- Z8 u# ?+ t( g; f. kFOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
% ^" ?7 {/ C* b4 |. N* qCROWN DRIVEN GWAR ONLY

4.
NORMAL PRESSURE ANGLE 20”

5.
NORMAL DIAMETRAL PITCH 8

6.
NORMAL CIRAULAR PITCH 0.3927

7.
' m7 {# c; K: T% s: l) qHELIX ANGLE:16.6011

8.
+ N' I/ Q5 c0 z, PBACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
* _0 n. \0 L2 Z6 KMATERIAL: AISI 8620

10.
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
TO BE 25-40 RC.

11.
7 |# k! Y: H/ |7 Z2 w# KRETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
% K6 P. E4 {7 pEACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
5 I7 ~+ |4 O5 M. d7 xREMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

  X% w5 H$ V8 I2 u沒有人翻譯,找到了資料,不知道對不對!望高手出來指正!
        齒輪制造標準和精度等級：ANSI/AGMA 2000-A88，精度12級，全深，全倒角。
        齒向、齒形修緣和漸開線輪廓公差按54773379圖紙規定。
        僅驅動齒輪鼓形修整。
        齒形壓力角20º
) R! k2 `' J- o' H% O        節徑DP=10
        齒距：0.3142
        螺旋角：15.9355º
. \; L$ b) Q& l9 J4 p7 O+ e        在齒輪嚙合中心距5.5118”上，側隙要求在0.006” ~0.010”之間。
" o0 r# d( ~, }1 m; h1 y        齒輪材料：AISI 8620
        滲碳層0.025”~0.040”有效深度，表面硬度為57~61Rc，芯部硬度25~40Rc。
        殘余奧氏體最大5%目測檢查。
; m% ]1 q4 u6 D' Z5 Q5 m0 P        每個周轉盒內只能裝一個齒輪組，周轉盒外標記齒輪組圖號，齒輪表面須按圖示部位用電蝕法標記零件號和供貨商代碼，字高約0.25。
        攻絲后，去除螺紋孔內的鐵屑。

qvzhiwei

樓上玩意的好專業，佩服！！！

another

二樓挺專業的···感覺還不錯，很值得學習。