求翻譯

jackline

外語不精，求達人翻譯，謝謝

; r. W7 Q- y/ \8 z4 H1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm

2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
% u+ M4 B1 ]3 K3：直線度超差：實測導軌止口直線度0.26mm（中凹）
4：尺寸超差：  圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
2 f# x* e# w5 ~4 P" s7 I6 e5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片
- K* S4 y0 y* `) @: Q6 _

神奇寶貝

1.Perpendicularity is out of tolerance: drawing's  requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
8 X( O0 C- T9 c- ?4 l' N2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
: S2 P$ H+ _  L3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
4. Dimension is out of tolerance: drawing's  requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

jackline

回復 jackline 的帖子
! M& p. C/ ]! O: d
2 g, h% a, a' ]) p2 X7 }' u受益匪淺，灰常感謝
3 t2 C, ~" ~; R( V$ Z  L+ V還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？
5 P( i6 K7 ^- u7 I) e6 g( K
$ @% I/ O6 Q7 Z( q

神奇寶貝

jackline 發表于 2011-7-7 20:06
回復 jackline 的帖子
% X( O% U# _0 l% `
. T5 u1 j# j& I受益匪淺，灰常感謝

) w2 @, F0 k  ?4 r7 {% h7 ~沒用過，也沒聽別人這樣用過

采彡銫莎氵莫

是和公司有關的，又學習了

wugqtop

jackline 發表于 2011-7-7 20:06
+ t' g2 \0 k& l  w- P) B回復 jackline 的帖子

8 }& W' `- e. o1 ~9 n* N7 H受益匪淺，灰常感謝

dimension out of tolerance
$ N& y- f0 s$ ~2 z& ?

kason127

用google翻譯好了！！